Explore 43 capabilities across seven categories. Use the software’s familiar names, or search by a task, protocol or tool.
Explore real application screens below. Select any image to enlarge it; captions identify setup states and demonstration data.
43 of 43 capabilities shown
License Required Relevant entitlement required; a bundle may already include it. Beta Applies only to the marked feature or providers. Unmarked items still depend on the issued software licence, permissions and setup. View licence guidance ↗
01 / Test Development
Build, reuse and validate the test logic.
Select a view. Enlarge the image to read individual fields.
Sequences & groups
Organise child steps, collapse long flows, copy groups and map imported devices.
Explore capability
Measurements, variables & formulas
Decode replies, capture variables, apply scaling and compare measured values with product limits.
Explore capabilityLoops & sweeps
Repeat checks with configured ranges, step sizes, dwell and point-by-point evidence.
Explore capabilityRun controls & live debug
Run a step, group, range or complete flow and inspect replies before production handover.
Explore capabilityRAJU BROS AI Assistance
Draft sequence content from supported documents and structured inputs for engineering review.
02 / Devices
Connect equipment and develop with supported I/O.
Devices & USB identity
Configure named instruments and locate supported serial devices after Windows changes their COM ports.
Explore capabilityDAQ & live I/O
Configure supported channels, scaling, calibration, live input monitoring and guarded output controls.
Explore capabilityUDAQ / RS485 relay sequences
Arrange relay actions and timing, trial the commands and link the operation to a test flow.
Explore capabilityVirtual devices
Launch Virtual Machine simulation profiles, exercise configured logic and then validate the physical station.
Explore capability
03 / Production
Identify the product and control the operator workflow.
Select a view. Enlarge the image to read individual fields.
Models & barcodes
Set required slots, validation, duplicate rules, interlocking and scan capture for each model.
Explore capabilityProduction & test plans
Assign models, flows and DUT positions for sequential or parallel operation, batch scanning and rolling lanes.
Explore capabilityGolden samples & start rules
Configure known OK/NG master checks and the conditions that admit a unit into production.
Explore capabilityProduction rules & recovery
Define RX, handling idle, reset, completion, NG-bin and report-recovery behaviour.
Explore capabilityOperator messages & acknowledgements
Show configured step instructions and require operator acknowledgement where the process calls for it.
Explore capabilityLabels & print verification
Design labels, manage serials and configure print triggers and required printed-code scans.
04 / Factory Integration
Exchange records, share visibility and send notifications.
File-based MES & interlocking
Define CSV/TXT records, folders, periods, model profiles and before-test file checks.
Explore capabilityNetwork MES
Configure supported TCP Raw or HTTP/HTTPS exchanges, payloads, accepted replies and controlled trials.
Confirm the required MES package and receiving-system contract.
Explore capabilityData Link
Reuse requests, map response values and variables, and review result exchange and delivery recovery.
Smart Factory Monitoring
Share approved, read-only station information with paired monitors on a trusted local network.
Quality Alerts
Configure recipients, model policies, severity, summaries, schedules and delivery recovery.
05 / Analytics
Move from production totals to the individual result.
KPI Dashboard
Review totals, pass rate, failed attempts, production trends, cycle time and handling time together.
Explore capabilityFailure Analysis
Compare monitored checks by failure count, failure rate and configured limits to focus an investigation.
Explore capabilityModel Analysis
Compare production totals, pass rates and cycle times across models; review the available efficiency views.
Explore capabilityBarcode Search & history
Find a unit’s saved attempts, measurements, limits and available attachments, including retests.
Explore capabilityReports, exports & archives
Filter retained records and configure supported CSV, TXT and PDF output, names and destinations.
Explore capabilityCycle Time Audit
Review controllable waits, save a timing trial and validate results before applying it to production.
Explore capability
06 / Engineering
Commission, inspect, program and maintain the station.
Select a view. Enlarge the image to read individual fields.
Communication Studio & Byte Lab
Trial commands, inspect TX/RX traffic and decode received bytes with the required byte order and scaling.
Explore capabilityCAN, CAN FD, LIN & UDS
Build bus sequences, inspect DBC signals and diagnostic traffic, and retain trace evidence.
CAN/analyzer and LIN access depend on the selected operations.
Explore capabilityCAN Calibration
Prepare calibration steps, parameters and calculations around the approved product procedure.
CAN Calibration entitlement includes CAN access.
Explore capabilityCustom CRC
Develop and verify checksum methods using parameters, byte data and known test vectors.
General Programming
Configure supported firmware providers, tool inputs, verification rules and retained programming output.
ST-LINK, SEGGER Flasher and XDM4011 workspaces are Beta.
Explore capabilityUDAQ firmware programming
Use the dedicated UDAQ programming workflow with the required firmware, tool and verification settings.
Separate from ordinary relay sequences and I/O control.
Explore capabilityVision & thermal inspection
Configure regions, optical checks, reference samples and supported thermal-frame inspection.
IR Camera entitlement includes Vision access.
Explore capabilityWiring & fixture design
Build schematics, scaled panel layouts and connection records with design checks and engineering exports.
Fixture Maintenance
Track fixture counters, maintenance limits, due conditions and authorised resets with their history.
Explore capabilityService Records
Record service sessions, engineer work, status, close-out and follow-up information for station maintenance.
Explore capability
07 / Administration
Manage changes, access, station health and support.
Activity Log
Review recorded user sessions, actions and saved setting changes with previous and updated field values.
Explore capabilityDebug Log & Test Log
Search technical messages, exceptions and test-log entries using the permitted filters and export tools.
Explore capabilityMachine Health
Run health checks, review preventive advice and investigate retained failure evidence and support exports.
Explore capabilityUser roles & permissions
Manage users and control access to pages and actions for operation, maintenance and configuration.
Explore capabilityStation & shift configuration
Maintain station identity, Shift Master, execution policies and report settings for the production setup.
Explore capabilityBackup, recovery & updates
Configure backups and follow the supported update and recovery procedures when maintaining a station.
Explore capabilityDocumentation & support
Use the customer manual, contextual HOW TO and keyboard guidance; video lessons are coming to the Learning Centre.
Explore capabilityNo matching capabilities
Try a broader term or clear the category and search filters.
